Featured Products
WIFI Receiver Sonoff POW R2 ON / OFF 3500W with Monitoring of Electric Consumption
The Sonow POW R2 WIFI Receiver has a Relay (ON / OFF) output of up to 3500W and also with the Receiver you can monitor the power consumption.
This receiver, as mentioned above, monitors the electricity consumption of a circuit by determining and sending notifications to your mobile phone through the eWeLink APP, with which you can decide what action to take to regulate that consumption. So you can also automate the Receiver for when the consumption reaches a certain value the programmed action is carried out.
For more information you can consult the user manual that comes with the Receiver.
SMD 5050 High Intensity LED Strip - 150LED/16.4ft - Multicolor / RGB
The listed price is for 1 Unit/Roll = 5mt / 16.40ft.
The Non-Waterproof SMD 5050 LED Flexible Strip comes in a roll of 16.4ft (5mt).
This strip comes in RGB / Multicolor. Through the use of a RGB LED Controller (not included), you can set to any color and create lighting effects in large spaces.
Designed for both the lighting professional and amateur, these LED Strips are very easy to install and use 3M Tape backing for easy mounting. Just peel and stick to any clean flat surface.
How to buy??: The listed price is for 5mts/16.4ft. If you select a quantity of "1", you will get 5mts/16.4ft of LED Strip. We have different prices depending on the quantity you need. THE MORE YOU BUY THE MORE YOU SAVE!!!
Technical Data:
Working Voltage: DC12V
Working Current: per 1mt/3.28ft.: 0.6A (7.2W)
per 5mt/16.4ft.: 3A (36W)
LED Type: RGB SMD 5050
LED #: 30LEDs/3.28ft.
150LEDs/roll (5mt / 16.40ft.)
LED Lifetime: 40,000h
Protection Rating: IP20 (Non-Waterproof)- For indoor use only (in dry locations)
Fully Dimmable
Cuttable into 3-LEDs (100mm / 3.93") on the marked sections and rejoined by a simple solder or you can use our connectors which are solder-less for easy installation
3M Tape backing for easy mounting
Optical Characteristics (per roll):
Wavelength:
Red: 625nm
Green: 525nm
Blue: 465nm
Lumen:
Red: 360Lm
Green: 540Lm
Blue: 270Lm
Beam Pattern: 100°
Notes:
1- This product must only be powered by a DC12V Power Source. For 5mts/16.4ft. we recommend our "DC12V * 5A 60W Switching Power Supply - UL LISTED" which is perfect to connect up to 6mt/19.68ft. of this LED Strip.
2- Unplug your power source when cutting LED strips.
3- Pay close attention to the polarity of all connections: match positive to + and Negative to -.
4- Pay attention to the Ingress Protection.
5- If you cannot wire this product on your own, please contact us or contact a professional.
6- You must cut the strip with scissors on the section marked with two points of tin, preferred in the middle of these points, so that each strip will have tin for other connections.
7- Place the LED Strip with the adhesive backing and for permanent placing use a glue of your preference
8- Caution: Do not bend this LED Strips to a radius less than 15mm or bend it on horizontal plane, because it can cause damage to the strip and void the warranty.
9- We recommend connect up to 10mts./32.80ft. (2 rolls) of these strips at the same Power Supply for better use. For longer runs, another Power Supply and Amplifier are required.
10- Please confirm color, voltage, wattage and length before ordering.
12- 2-YEAR WARRANTY
To Use it, Don’t forget to buy the following:
Required:
DC12V Power Supply: It depends on the quantity or length of the LED Light you will setup. For best use, it should be about 20% stronger (Watts/Amps) than the total required to run your system. How?.
- For 5mts/16.4ft. we recommend our "DC12V * 5A 60W Switching Power Supply - UL LISTED" which is perfect to connect up to 6mt/19.68ft. of this LED Strip.
RGB LED Controller: it allows you to create color lighting effects in large spaces.
Amplifier: for connecting more than 2 rolls of this Strips and maintaining light quality.
Required:
RGB LED Strip Connector: for connecting multiple light strips at any angle.
Silicone Mounting Clips: for mounting the strip especially on timber or concrete.
Heat Shrink Tubing: for waterproofing and isolating wires
All specifications are subject to change without notice
WIFI Sonoff DUAL Receiver for Combined Effects ON / OFF 3500W
The WIFI Sonoff DUAL Receiver for Combined Effects has a Relay (ON / OFF) output of up to 3500W.
This Receiver serves to Power on / off effects from two independent circuits. Like the rest of the Sonoff products, the Receiver can be controlled with the eWeLink app from your mobile, or you can moderate it by voice command via Alexa or Google Home.
For more information you can consult the user manual that comes with the Receiver.
